Braeburn 5000 User Manual download pdf

WARNING

Important Safety Information

Premier Series

Programmable Thermostats

• Always turn off power to the air conditioning or heating system prior to

installing, removing, cleaning or servicing thermostat.

• This thermostat requires either 24 Volts AC Power or two (2) properly installed

“AA” alkaline batteries for normal operation and control of the heating or

cooling system.

• This thermostat requires two (2) properly installed “AA” alkaline batteries to

retain clock setting in the event of loss of AC Power due to a power outage or

rolling blackouts when used as a hardwired thermostat.

• This thermostat should only be used as described in this manual. Any other

use is not recommended and will void the warranty.

Speciﬁcations

Installation

Testing Your New Thermostat

Programming User Settings

Setting Your Energy

Saving Program

Temperature Adjustment

Additional Operation

Features

Battery Replacement

Troubleshooting

Wiring Diagrams

Speciﬁcations

• Compatibility: Compatible with low voltage single stage gas, oil or

electric heating or cooling systems, including single stage heat pumps.

This thermostat can also be used on 250mv to 750mv millivolt heating

only systems.

• Terminations: Rc, Rh, B, O, Y, W, G, C

Speciﬁcations

cont.

Installation

MODEL

Single Stage Heat / Cool

7 Day or 5 - 2 Day Programmable

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

3 amp total maximum load (all terminals)

• Control Range: 45˚ - 90˚ F (7˚ - 32˚ C)

• Accuracy: +/- 1˚ F (+/- .5˚ C)

• AC Power: 18-30 Volt AC

• DC Power: 3.0 Volt DC (2 AA Alkaline batteries included)

Replacing Existing Thermostat

Most thermostats have three parts:

• The cover, which may snap or hinge over the existing thermostat.

• The electronics or body, which controls the existing system.

• The sub-base, where the wires attach through the wall to the existing system.

1. Always turn off power to the air conditioning and heating system prior to

removing existing thermostat.

2. Carefully remove the cover and electronics body from the old thermostat

sub-base. Depending on the brand, these parts may pull off or need to be

unscrewed. The old sub-base should remain wired and on the wall until steps

4 and 5.

3. Label every old wire with the letter of the connection to which the wire is

attached. Example letters are R, M, and Y etc. Depending on the brand of the

old thermostat, your letters may be different.

4. After labeling the old wires, loosen each connection and remove them from old

sub-base. Secure the wires to prevent them from slipping into the hole in the wall.

5. Remove the old sub-base from the wall, again being careful that the wires do

not slip into the hole in the wall.

6. Use the chart below to determine the new thermostat connections. As an

example, if the old thermostat had a G or F connection, it goes to G on the new

thermostat. Using a pencil and the chart below, circle the letter of each wire

removed from the old thermostat.

Old Terminal from

Existing Thermostat

New Terminal for

New Thermostat

Terminal

Description

V or RC Rc Cooling Transformer

M, 4, Rh or R Rh Heating Transformer

B B Reversing Valve (Heating)

O O Reversing Valve (Cooling)

Y Y Cooling Control

H, W or 4 W Heating Control

G or F G Fan Control

C C 24 Volt AC, Transformer

Common

5000

NOTE: This thermostat is designed for use with 24 Volt AC low voltage single

stage gas, oil or electric heating or cooling systems, including single stage heat

pumps. This thermostat can also be used on 250mv to 750mv millivolt heating

only systems. Do not use this thermostat on applications with voltages above

30 Volts AC.

Before Installing, Programming or Operating,

PLEASE READ ALL INSTRUCTIONS

1 2 3 4 5 6 7 8 9

Summary of Contents

Page 1 - Premier Series

WARNINGImportant Safety Information1Premier SeriesProgrammable Thermostats• Always turn off power to the air conditioning or heating system prior to

Page 2 - Testing Your New Thermostat

2 3WARNING!Read BEFORE TestingInstallation2cont.Installing Your New ThermostatNOTE: When installing this thermostat in a new location, following a fe

Page 3 - Programming User Settings

4Default Thermostat SettingsSetting Thermostat User OptionsSetting Current Time of Day and Day of Week5cont.Programming User Settings4NOTE: It is imp

Page 4

6 7Setting the Extended Hold Time (continued)Setting Your Energy Saving Program–Tips Before Starting• It is important for you to set the current time

Page 5 - (continued from page 8)

81. Place the system switch in the HEAT mode of operation. 2. Press the PROG button to enter the Program setting mode. MORN set point of th

Page 6 - Additional Operation Features

10Temperature Adjustment6Review Set Temperature1. Press and hold the or button. The current set point temperature will be displayed in pl

Page 7 - Battery Replacement

Compressor ProtectionThis thermostat includes an automatic compressor protection feature to avoid potential damage to the cooling system from short cy

Page 8 - Troubleshooting

Troubleshooting9Troubleshooting9cont.Symptom: HI is shown in the thermostat display where the room temperature is normally displayed.Potential Soluti

Page 9 - LIMITED WARRANTY

Single Stage Conventional Systems (Dual Transformer)16Wiring Diagrams10Single Stage Conventional Systems (Single Transformer)Rc Rh BFactory InstalledJ