Braeburn 5300 User Manual download pdf (Page 2)

PROGRAMMING

USER SETTINGS

2.1 Setting Current Time of Day and Day of Week

NOTE:

It is important for you to correctly set the current time of day (note AM/PM indicator in display), and the

current day of week to avoid problems with program execution.

1. When in normal operating mode, press the DAY/TIME keypad button.

The LCD display will be cleared except for the time, am/pm indicator, day

of week indicator and SET. The hour portion of the time will ﬂash. Press

the or button to set the current hour.

2. Press the DAY/TIME button again; the minute portion of the time will

ﬂash. Press the or button to set the current minute.

3. Press the DAY/TIME button again. The day of week indicator will ﬂash.

Press the or button to set the current day of week.

NOTE: The thermostat will return to normal operating mode automatically after 30 seconds if no buttons are pressed. It will

also return to normal operating mode immediately if the RETURN button is pressed.

2.2 Setting Fan Control

The Fan Control has 4 modes of operation – AUTO, ON, CIRC (Recirculate) and PROG (Program). The Fan mode can be selected

by pressing the Fan button and scrolling through the modes of operation.

AUTO: In the Auto mode, the fan is turned on whenever there is a call for heating or cooling. The Auto mode is not available

if the FAN LOCK was enabled in the Installer Options (see Installer Guide).

ON: The fan runs continually.

CIRC: The fan runs intermittently (approximately every 24 minutes) even if there is no call for heating or cooling. This feature

recirculates the air for more even temperature distribution, and is available in all heating and cooling modes. See section

2.4.9 and 3.12 for instructions on programming fan run times.

PROG: The fan will remain on for the entire programmed time period if it is set to ON during programming. The PROG mode

is not available if the recirculating FAN LOCK was enabled in the Installer Options, or if the thermostat has been

installed in non-programmable operating mode.

SET

PROGRAMMING

USER SETTINGS

2.3 Setting Thermostat System Selection

The system can be selected by pressing the System button. There are ﬁve possible settings to select from –

AUTO, COOL, OFF, HEAT and EMER.

AUTO: Auto can only be selected if it was enabled by the installer (see Section 4 of the Installer Guide). If AUTO

is selected, the system cycles between heating and cooling as determined by the set points. AUTO will

be displayed constantly with either HEAT or COOL depending on the indoor temperature and programmed

set temperatures.

COOL: Selected for system to run air conditioning. When there is a 1st stage cooling call, COOL will ﬂash.

In a 2 stage system, COOL2 will be displayed for a 2nd stage cooling call.

OFF: System is off. The room temperature, day and time will be displayed. Any extended hold or temporary

override will remain in effect unless they expire. The HEAT setting can be reviewed using the and

buttons, but there is no heat function.

HEAT: Selected for system to run heat. When there is a 1st stage heating call, HEAT will ﬂash. In a 2 stage

system, AUX will be displayed along with HEAT for a 2nd stage heating call. AUX will be displayed along

with HEAT2 for a 3rd stage heating call.

EMER: This is only available for 2 or 3 Stage Heat Pump systems. If selected, EMER will be displayed constantly.

When there is a heating call HEAT will ﬂash.

2.4 Setting Thermostat User Options

The default user options are compatible with most systems and applications. They are normally set at the time

of installation and usually do not require any modiﬁcation under normal operating conditions. If you would like to

change these settings simply follow the instructions below.

NOTE:

If at any time while in the User Options Mode, you decide not to make any further changes, you can wait

30 seconds without pressing any buttons to return to the normal operating mode; or press the PROG and RETURN

buttons together to return to the normal mode. The RETURN button scrolls forward in the User Options. The PROG

button scrolls backward in the User Options.

NOTE: The various stage differential settings are the same for both the heating and cooling systems.

cont.

1 2 3 4 5 6 7 ... 14 15

Comments to this Manuals

No comments

Braeburn 5300 User Manual Page 2

Comments to this Manuals

Related products and manuals for Thermostats Braeburn 5300